|
608 LT
I.D. No.
169019000001 & Up I.D. No. 169026300001
& Up |
611 LT
LT I.D. No. 169034500001 & Up |
| ENGINE |
|
|
| Make |
Briggs & Stratton |
Briggs & Stratton
|
| Model No |
191707 |
252707 |
| Horsepower |
8 (6.0 kW)
- 3600 RPM |
11 (8.3
kW) @ 3600 RPM |
| Cycles |
4 |
4 |
| Cylinders |
1 |
1 |
| Bore |
3" (76.2 mm) |
3-7/16" (87.4 mm)
|
| Stroke |
2-3/4" (69.9 mm) |
2-5/8" (66.5 mm) |
| Displacement |
19.44 cu. in. (319
cm3) |
24.36 cu. in. (399
cm3) |
| Crankshaft
|
Vertical |
Vertical |
| Electrical System |
|
|
| Alternator |
|
|
| Battery
|
12 Volt - 32 Amp.- Hr.
(Automotive) |
12 Volt - 39 Amp.
- Hr |
| Ignition |
Key Switch |
Key Switch |
| Ignition: |
|
|
| Type |
Flywheel Magneto w/Key Switch
Dust Proof Breaker Enclosure Under Flywheel
|
Flywheel Magneto w/Key Switch |
| Governor: |
|
|
| Type |
Adjustable, Mechanical, Running in Oil |
Adjustable, Mechanical,
Running in Oil |
| Range
|
1800 - 3400 RPM |
1750 - 3400 RPM
|
| Air Cleaner
|
Sealed Joint Housing,
Oil Foam Element |
Sealed Joint Housing,
Oil Foam Element |
| Element |
Reusable Polyurethane
Foam |
Reusable Polyurethane Foam |
| Crankcase: |
|
|
| Breather |
Ventilated through Carburetor |
|
| Lubrication |
Gear Impeller System |
Gear Impeller System
|
| Oil Capacity
|
2-1/4 Pints
(1.1 litres) |
3 Pints (1.4 litres) |
| Fuel Tank: |
|
|
| Material |
High Density
Polyethylene |
High Density
Polyethylene |
| Fuel Level Gauge |
Built into Filler Cap |
Built into Filler Cap
|
| Capacity
|
2.2 Gallons (8.3 litres) |
2.2 Gallons (8.3
litres)
|
| Muffler |
Quiet Compact Low Back Pressure |
Lo-Tons |
| TRANSMISSION |
|
|
| Type |
All Spur Gear, Running in Oil Bath |
All Spur Gear, Running
in Oil Bath |
| Material: |
|
|
| Gears
|
Heat Treated |
Heat Treated |
| Shafts |
Hardened and Ground |
Hardened and Ground
|
| Bearings |
Needle Type Roller |
Needle Type Roller |
| Lubrication: |
|
|
| SAE 90 Oil Capacity
|
1-1/2 Pints (.7 litres)
|
1-1/2 Pints
(.7 litres) |
| Speeds: |
3 Forward, 1 Reverse |
3 Forward, 1 Reverse |
| 1st |
1.55 MPH (2.49 km/h) |
1.55 MPH (2.49 km/h)
|
| 2nd |
3.04 MPH (4.89 km/h) |
3.04 MPH (4.89 km/h)
|
| 3rd |
4.48 MPH (7.21 km/h) |
4.48 MPH (7.21 km/h |
| Reverse |
2.13 MPH (3.43 km/h) |
2.13 MPH (3.43 km/h)
|
| Differential |
Gear Type |
Gear Type |
| CHASSIS |
|
|
| Frame
|
Channel, Heavy Gauge
Steel |
Channel, Heavy Gauge
Steel |
| Engine Mounting |
Above Front Axle |
Above Front Axle
|
| Pivot Point
Location |
At Front Axle |
At Front Axle |
| Rear Wheel: |
|
|
| Tire Size |
18 x 8.50 x 8 |
18 x 9.50 x 8
|
| Pneumatic Inflation
Pressure |
6 - 8 PSI (41 - 55 kPa) |
6 - 8 PSI (41 - 55 kPa) |
| Front Wheels: |
|
|
| Tire Size
|
13 x 5.00
x 6 |
13 x 5.00 x 6
|
| Pneumatic Inflation Pressure |
12 - 15 PSI (83 - 103 kPa)
|
12 - 15 PSI (83
- 103
kPa) |
| Bearings |
Sintered Iron with
Grease Fittings |
Sintered Iron with Grease Fittings |
|
Source: 600 LT Series Tractors Service
Manual, No. 9003479, 11/79, courtesy of Larry Comer
|
